IOT 제품 > 아두이노
플라이메이플 컨트롤러 ( Flymaple-A flight controller with 10 DOF IMU )
 

플라이메이플 컨트롤러 ( Flymaple-A flight controller with 10 DOF IMU )
 

플라이메이플 비행 컨트롤러 ( Flymaple-A flight controller with 10 DOF IMU )

플라이메이플 비행 컨트롤러 ( Flymaple-A flight controller with 10 DOF IMU )

플라이메이플 비행 컨트롤러 ( Flymaple-A flight controller with 10 DOF IMU )
 


Introduction
  •  

     



     
    Applications

     

    Flymaple is a Quadcopter controller board, based on the Maple Project. The FlyMaple embeds a STM32F103RET6 (ARM Cortex-M3) as it's main MCU. It integrates a 3-Axis accelerometer,a 3-Axis gyroscope,a 3-Axis compass and a barometric pressure sensor. By using the 10 dgrees of freedom IMUs and powerful 72MHz high-performation microcontroller, flymaple is powerful enough to handle a complex algorithm and manage a robot motion system at the same time.
     
    The design of flymaple is based on the maple, which is an arduino sytle ARM processor. The Maple IDE will make Processing/Arduino programmers feel right at home. If you're familiar with Arduino then you can get started with the Maple IDE quite easily.
     
    Flymaple is aimed to run on the balancing robots,mobile platform,helicopters and quadcopters which require IMUs and high performance real time controllers. It has an amazing scalability, because it's compatible with the Arduino shields. FlyMaple extends 6 PWM channels and 8 channels for GPIO for controlling ESC/Servo and capturing RC receiver input.
    • Aircraft
    • Balancing robots
    • Indoor inertial navigation
    • Altimeter

Specification

  • Working Voltage: 5v
  • STM32 Operating Voltage: 3.3v
  • 7~12v External Power supply from the 2p JST connector
  • Output Voltage: 3.3v/5v or External input power
  • Microcontroller: STM32F103
  • Running at 72Mhz with 32bit Arduino sytle ARM processor(Cortex-M3)
  • Bootloader: Leaflabs Maple RET6 Edition
  • 10 Degrees of Freedom on a single, flat board:
    • ITG-3200 - triple-axis digital-output gyroscope
    • ADXL345 - 13-bit resolution, ±16g, triple-axis accelerometer
    • HMC5883L - triple-axis, digital magnetometer
    • BMP085 - high-precision barometric pressure sensor
  • Programable through an Arduino-based development environment - Maple IDE
  • Compatible with most of Arduino shields
  • Extends 6 channels PWM pins for controlling ESC/Servo
  • Extends 8 channels GPIO for capturing RC receiver output
  • 3x 4p JST connectors:
    • Serial port 1
    • GPS extension port
    • I2C interface
  • Size: 50x50x12mm
  • Weight: 15g
  • Envionment Friendly: Rohs Compliance



Document




Shipping List

  • Flymaple v1.1 x1

이전글
라즈베리파이 2 / B+ 확장 쉴드 X200 ( Expansion Shield X200 for Raspberry Pi B and 2 ) 2015/07/20
플랙시블 태양전지 패널 - 2V 1W ( 2V 1W Thin-film Flexible Solar Panel ) 2015/07/15
다음글
Flexi-Strip 디지털 RGB LED 스크립 2m 생활방수 (144픽셀/m) 2015/08/07
ESP8266 based WiFi module - SPI supported 2015/08/07